Investigation of the impact of changes in demand forecasting method on the financial performance of an electricity supply undertaking

Peak demand forecasts obtained from six different univariate forecasting methods, under a range of conditions, were used to drive a capacity acquisition model of a large electrical supply system; and the resulting physical and financial performance of the model was observed for each set of forecasts. The results obtained are discussed in the context of their implications for the choice of load forecasting method used in capacity acquisition planning by a power supply undertaking.     

电力负荷削峰减载系统在珠钢电炉的应用

借助现场采集装置,在计算机上获取每一分钟的冶炼工艺电能需求量,显示当前15分钟时段已发生的电耗量,调整用户设定,实现需量自动刷新、报警和专家分析推荐后续用量;实现平稳用电并减少对电网冲击,同时降低电能最大需用量以减少成本。     

炼铁生产环境负荷分析和预测研究

利用寿命周期评价的思想，计算了炼铁生产过程中的环境负荷，并分析了各因素对环境负荷的影响，运用神经网络对炼铁生产过程环境负荷进行了预测。     

Analysis of the Ductile Strength of Welds Weakened by Notches in Longitudinally Welded Pipes of Large Diameter by the Method of Slip Lines

We study the stressed state of an inhomogeneous welded joint containing an interlayer of a more high-strength material under the action of tensile loads. It is assumed that the contact boundary has a cracklike defect. We deduce analytic dependences of the fracture load on the mechanical inhomogeneity of the joint, thickness of the interlayer, and depth of the defect. The maximum depth of the defect to which the joint is insensitive is established. The proposed theoretical results are innovative and agree with the experimental data obtained for specimens cut out from a pipe of 14KhGS steel.     

就地补偿在动力厂水泵电机上的应用实例

就我公司动力厂给水车间155kW水泵电机无功就地补偿的可行性及经济效益进行了分析和研究，对工厂用电如何节能降耗有一定的参考价值。     

Limit load analysis of strength undermatched welded T-joints under bending

An increasing amount of laser beam welded T‐joints (e.g. skin‐stringer) of aluminium alloys are now in use in advanced fuselage applications designed as ‘integral structures’ for weight and cost savings. It is known that weld joints generally show lower strength (undermatching) than base metal in both laser beam and friction stir welded joints of 6xxx series Al‐alloys. Damage tolerance considerations in terms of the residual strength of such joints require limit load solutions to be used in engineering fitness‐for‐service (FFS) analysis. The paper, therefore, provides an upper bound limit load solution in closed form for welded T‐joints (idealized) with strength undermatching and subject to a bending moment. In addition to the necessary requirements of the upper bound theorem, the kinematically admissible velocity field chosen leads to a stress field, which satisfies the equilibrium equations and some stress boundary conditions in the plastic zone. This is an advantage of the solution and, therefore, it is expected that the upper bound obtained is close to the exact limit load of such joints.     

Reliability Analysis of Single-Degree-of-Freedom Elastoplastic Systems. II: Suboptimal Excitations

A method for constructing an approximation of the critical excitation that drives an elastoplastic system from rest to a target threshold at a specified time instant, referred to as the “suboptimal excitation,” is presented in this paper. It is based on the observations gained from study of the critical excitations in the companion paper. Essentially, for the usual case of interest where the failure time is not small compared to the natural period, the duration of the positive and negative pulses of the critical excitation are roughly equal to half of the natural period. This consideration allows for a simple intuitive approximation of the critical excitation. The amplitudes of the positive and negative pulses are obtained in closed forms using energy balance. Numerical investigations show that the critical excitations are well approximated by the suboptimal excitations.     

台缙高速公路苍岭隧道水文地质勘察与涌水量预测

以台缙高速公路苍岭隧道为例，通过水文地质综合勘探方法，查明隧道不同裂隙发育程度岩体的渗透系数K值。然后利用地下水动力学法、地下水径流模数法对隧道开挖涌水量进行了预测。通过施工检验发现，涌水段位置和涌水量总体较接近，说明预测工作对隧道的施工开挖和排水设计具有指导意义。     

新型复合弹簧的研究

提出一种金属圆锥弹簧与橡胶圆锥弹簧复合而成的弹簧．分析表明：它可以应用于弹性耦合激励振动筛和座式直线振动筛。     

微波宽频带功率负载的研究

介绍了５００Ｗ宽频带功率负载的设计及实验结果，并将研究成果扩展到１０～１０００Ｗ范围。负载主要技术指标：输入阻抗５０Ω，频带宽度０～１０００ＭＨｚ，电压驻波比≤１．１．表面最高温升△ｔ≤１００℃。